Oracle Enterprise Linux

Click here

CLI

Check mounts

esxcfg-nas -l | grep unmount
esxcfg-nas -r to remount

List all Vms on ESX Host

vim-cmd vmsvc/getallvms

Install vmware tools

vim-cmd vmsvc/tools.install 1123

Get Guest Information

vim-cmd vmsvc/get.guest 1504

SDK

Get VM Info

./vm/vminfo.pl --url https://vcenter.de-ent.com:443/sdk/vimService --username 'user' --password 'pass' --folder 'HR VM' --out /tmp/out

Enabling Swap

Create partition on the disk

[root@dstolprddb03-oracle ~]# fdisk -u /dev/sdb
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.


The number of cylinders for this disk is set to 4177.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)

Command (m for help): n
Command action
   e   extended
   p   primary partition (1-4)
p
Partition number (1-4): 1
First sector (63-67108800, default 63): 
Using default value 63
Last sector or +size or +sizeM or +sizeK (63-67108800, default 67108800): 
Using default value 67108800


Command (m for help): t
Selected partition 1
Hex code (type L to list codes): 82
Changed system type of partition 1 to 82 (Linux swap / Solaris)


Command (m for help): p

Disk /dev/sdb1: 34.3 GB, 34359706112 bytes
255 heads, 63 sectors/track, 4177 cylinders, total 67108801 sectors
Units = sectors of 1 * 512 = 512 bytes

     Device Boot      Start         End      Blocks   Id  System
/dev/sdb1p1              63    67108800    33554369   82  Linux swap / Solaris

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: Re-reading the partition table failed with error 22: Invalid argument.
The kernel still uses the old table.
The new table will be used at the next reboot.
Syncing disks.

Enable swap

mkswap -L SWAP-sdb1 /dev/sdb1
swapon /dev/sdb1

fstab Entry

LABEL=SWAP-sdb1         swap                    swap    defaults        0 0

Importing VM from one datacenter to another

Preparing Netapps

Locate the volume where the current datastore is (also note the folder name under 'Edit Settings')
Find snapmirror destination for the regular and swap volumes, break snapmirrors for both

Import the Virtual Machine

Change vcenter view to Datastores
- If adding a new DS, add the ds2data folder in the path
Find the destination volume in the gui, click on 'Browse Datastore'
Locate the folder name you found from the original VM datastore info, open it, and add the vmx file to inventory
- Rename it appropriately

Update New Virtual Machine

The swap disk usually gets mucked up, so remove it (do not remove from disk, just from the virtual machine) and re-add it
Update network vlan

Migrate the VM to a new netapp / volume

Click Migrate
Change Datastore
Click Advanced, then change the locations there. Config & HD1 should be on the same datastore
Select Thin Provisioned format

Add new disk to CentOS

Once the disk is added in vmware:

fdisk -u /dev/sdc
- p;
- w
mkfs -t ext4 /dev/sdc1
use blkid to get the uuid

Mbralign and Scanning

Running mbralign/mbrscan

Note: The VM can be powered on during a scan, but you must initiate the scan from an esx host on which the VM is not currently running. To do an mbralign, the VM must be powered off. Do not do this with centos6. They fixed it on their end.

/opt/netapp/santools/mbrscan *.vmdk
/opt/netapp/santools/mbralign --sparse *.vmdk

Fixing Broken MBR / Grub

Boot off a linux cd (rescue)
- To do this, as soon as the VM powers on, hit 'escape' once to get the bio boot menu.
At the prompt, type linux rescue
Once there, chroot to the location of the mounted image (should be /mnt/sysimage)
run fdisk -l to see which drive to install grub on
grub-install /dev/sda
Reboot, should work now.

More info [here]

Add Datastore to ESX Host in Vcenter

Change view to Hosts & Clusters
Click on the ESX host, open config tab
Click Add Storage...

Errors

Snapshot Error

    Clone virtual machine:Cannot create a quiesced snapshot because the (user-supplied) custom prefreeze script in the virtual machine exited with a nonzero return code.

Right click on the source VM, snapshots, snapshot manager, and delete snapshots.

Vmware

Contents